connecting… ECU gauge bus 0 gauges
Each card shows what that gauge displays. Planned gauges exist only on the hub, for laying out and assigning configs before the hardware arrives; link them to the real gauge later.
All gauges
Theme colourschange a shared colour: every widget using it, on every gauge, follows
Recordings
A recording is the live channel values ten times a second, kept on the hub. Play one and the simulator carries it to the gauges and the previews; Download it to open it in the online copy or on another hub.
ChannelNameValueUnit
Alerts
The hub checks these against the live data ten times a second. While an alert's condition holds, the gauges show its message, switch to another config or face, or both, and go back when it ends. Where two alerts apply to the same gauge, the one higher in the list wins. Changes are saved as you make them.
Config library
NameTitleFacesSizeAssigned to
Theme colourskept on the hub, shared by every config and gauge
Pick one from a widget's colour list, or write themecolour1, themecolour2 and so on in the JSON. Change one here and every widget using it changes with it, on every face of every gauge. Add colour adds up to 32; only the last can be removed, so a number always means the same colour.
Images
Backgrounds, logos and icons for the faces: use one in an image widget, or as a face's background. They are kept on the hub, and each gauge gets the ones its config uses over the gauge bus, before the config itself and only once. Smaller is quicker: the bus carries roughly 25 KB a second to each gauge alongside the live data.

Hub

SD card

With a card in the hub's slot, every drive is logged: every channel, ten times a second, as a CSV file per key-on, named by the hub's clock. Download a log here or read the card in a PC.

Time

The hub keeps the clock for the gauges: from the internet when it is on your home network, otherwise from this device, and from the clock chip on the carrier when one is fitted. Pick the zone the gauges should show.

Firmware

When it is on your home network the hub looks at oagauge.online once a day for a newer build and says so here; it installs one only when you press Install. Do that with the engine off: the hub restarts, and comes back to this build by itself if the new one fails to start. A firmware.bin built on a PC can be uploaded straight in.

Gauge firmware

Builds for the gauges are fetched from the site onto the hub. A gauge whose board has a newer build on the hub gets an Update firmware button on its card; the hub sends it over its own Wi-Fi.

Start-up intro

At key-on the gauges stay dark until each has announced itself, then play an intro one after another, left to right, in the order of the cards on the Gauges tab (the arrows on each card move it). A gauge that hears no hub plays its own after three seconds.

Access point

Always on. Join it to reach this page at http://192.168.4.1/.

Home Wi-Fi (optional)

The hub can also join your network, so a PC can open it without switching Wi-Fi.

Online account

Link this hub to your account at oagauge.online: sign in there, Settings, Link a hub, and type the code here. From then on the configs, images, theme colours and alerts you make on either side reach the other, over your home network.

Editing a face

click, dragselect a widget; move it. Guides snap it to the face centre and to other widgets
shift + clickadd to the selection; drag moves them together
Ctrl + Aselect every widget on the face
corner handlesresize: radius, width and height, or text size
knob aboverotate (snaps to 15 degrees); the start angle of a dial or ring
arrowsnudge by a pixel; with shift, ten
Deleteremove the selected widgets
Ctrl + Dduplicate them, a little to the right and down
Ctrl + Z, Ctrl + Yundo, redo (also the Undo and Redo buttons)
Escdeselect; close this
?this list

With two or more selected, Same x, Same y, Spread x and Spread y appear above the widget list. What you type in the JSON is kept in this browser until you save it: reopening a config offers the unsaved draft back.